MTD K-Style Návod k obsluze Strana 1

Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • WarrantyL600-Series Snow Thrower m K StyleMTD LLC, P.O. BOX

AdjustmentsSkidShoesThe snow thrower skid shoes are adjusted upward at the factoryfor shipping purposes. Adjust them downward, if desired, priorto ope

Controlsand Features4Drive ControlShift Lever/Chute Directional Controler ControlChute Assembly\,\Clean OutTool\Gas Cap\\OU FUl\AugersSkid ShoeSnow th

ThrottleControlThe throttle control is located on the rear of the engine. Itregulates the speed of the engine and will shut off the enginewhen moved i

ChuteDirectionalControlCHUTE DiRECTiONAL CONTROLCHUTE CHUTEROTATE ROTATELEFT RIGHTJThe chute directional control is located on the left side of thedas

OperationStarting the Enginel_lhllL ARNING! Always keep hands and feet clear ofmoving parts. Do not use a pressurized startingfluid. Vapors are flamma

RecoilStarterCAUTION! Do not pull the starter handle while theengine running.WARNING: To avoid unsupervised engineoperation, never leave the engine un

Maintenance&Adjustments6MaintenanceEngineRefer to the Engine Maintenance section.ShavePlate and Skid ShoesThe shave plate and skid shoes on the bo

AugerShaftAt least once a season, remove the shear pins from the augershaft. Spray lubricant inside the shaft and around the spacers andthe flange bea

DriveControlWhen the drive control is released and in the disengaged "up"position, the cable should have very little slack. It should NOT be

EngineMaintenance7WARNING! To prevent accidental start-up, shut offthe engine and remove the ignition key beforeperforming any type of engine maintena

ToTheOwner1ThankYouThank you for purchasing a Snow Thrower manufactured byMTD LLC. It was carefully engineered to provide excellentperformance when pr

5park Plugi_ WARNING? DO NOT check for spark with sparkplug removed. DO NOT crank engine with sparkplug removed.i_ WARNING! If the engine has been run

ServiceBelt ReplacementAuger BeltTo remove and replace your snow thrower's auger belt, proceedas follows:I. Allow the engine to run until it is o

3_Remove the belt from around the auger pulley, and slip thebelt between the support bracket and the auger pulley.See Fig. 8-5.JFigure 8-54_Reassemble

6_Slip the drive belt offthe pulley and between frictionwheel and friction wheel disc. See Fig. 8-7.Figure 8-7Remove and replace belt in the reverse o

5_6_Carefully remove the hex nut which secures the hex shaftto the snow thrower frame and lightly tap the shaft's end todislodge the ball bearing

Troubleshooting9ProblemEngine fails to startEngine runs erraticEngine overheatsExcessive vibrationLoss of powerUnit fails to propel itselfUnit fails t

ReplacementParts1Component l Part Number and Description929-0071Extention Cord, 110V954-04050 Auger Drive Belt754-0367 Wheel Drive Belt684-04153935-04

127

SECTION11= NOTES

SECTION11 = NOTES 29

ImportantSafeOperationPractices2WARNING! This symbol points out important safety instructions which, if not followed,could endanger the personal safet

MTD CONSUMER GROUP INC (MTD), the California Air Resources Board (CARB)and the United States Environment Protection Agency (U. S. EPA)Emission Control

(4)Repairorreplacementofanywarrantedpartunderthewarrantyprovisionsofthisarticlemustbeperformedatnochargetotheowneratawarrantystation.(5)Notwithstandin

MANUFACTURER'S LiMiTED WARRANTY FORThe limited warranty set forth below is given by MTD LLC withrespect to new merchandise purchased and used in

SafeHandling of GasolineTo avoid personal injury or property damage use extreme carein handling gasoline. Gasoline is extremely flammable and thevapor

Clearinga CloggedDischargeChuteHand contact with the rotating impeller inside the dischargechute is the most common cause of injury associated with sn

Safety SymbolsThis page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on themach

Assembly& Set-Up3Contentsof CartonOne Snow ThrowerOne Snow Thrower Operator'sManualTwo Replacement Auger Shear Pins One Product Registration

3 Set-UpFinish securing chute control assembly to chute supportbracket with wing nut and hex screw removed earlier.See Fig. 3-4.Figure 3-44. Check tha

Fuel RecommendationsUse automotive gasoline (unleaded or low leaded to minimizecombustion chamber deposits) with a minimum of 87 octane.Gasoline with